Yes, the Curt Spyder Goooseneck/Fifth Wheel Adapter part # 16085 does come with the needed pins to secure it to your fifth wheel rails. view full answer...
Currently I do not see Lippert has a specific set of instructions for the Replacement Control Panel Kit with Touchpad # LC34UJ. This is not uncommon since the harness has the plug and play connections and there is no hardwiring required. Both the touchpad and control panel are held in part with screws. Also as the harness is going to be ran by the RV manufacturer there are no specific ways to say the harness has to be ran except for keeping it away from heat sources and moving parts. view full answer...
Aries makes their grille guards and their hardware kits specifically for the vehicles so unfortunately it's not as simple as swapping hardware kits to fit the guard to a new vehicle. Only solution would be an all new guard like the part # AA3045 that fits your 2000 Ford Excursion or to find a local welder who could possibly fabricate something for you. view full answer...
From previous customers with a 2020 Montana High Country we have determined that your 295RL most likely comes with the 1116 pin box so for a Gen-Y gooseneck adapter you'd want the part # GY43FR. If your current pin box is 12-1/2 inches wide then this is accurate. If instead you find it's 12 inches wide you'd need the part # GY36FR as you instead of the 1621 pin box. view full answer...
Thanks for all the info you provided Chris! Based on your axle being a Dexter #11 the correct lift kit is the part # K71-724-02 that you referenced and you can disregard the capacity numbers. view full answer...
We have all the parts you will need to add a set of electric brakes to a Master Tow 80THD tow dolly but they don't come in kits. I recommend installing electric brakes. It looks like Master Tow includes brake mounting flanges so you will need the following parts:
Brake Assembly - Electric Trailer Brake Kit item # AKEBRK-35 - Sold as a pair
Hub & Drum Assembly - Trailer Hub and Drum Assembly item # AKHD-545-35-K - Sold individually you'll need two.
Trailer Wiring Junction Box item #... view full answer...
The stoplight switch # RM-751490 and the monitor light that's included in the Demco SBS Stay-IN-Play DUO Supplemental Braking System # SM99251 do the same job, so you wouldn't need it if you decided to go with the Stay-IN-Play DUO.
The stoplight switch would be needed if you we to use a different permanent braking system. view full answer...
The Detail K2 Rampage II Elite Snowplow # K2RAMP8219ELT will work with your lifted 1978 Chevy Cheyenne as long as the front receiver is 13" - 18" from the ground to the bottom of the receiver. If your receiver is taller than that then you'll need to look for a specialized snowplow for your application. view full answer...
I would be happy to put together a list of parts to flat tow your vehicle. Roadmaster is a great brand and what I typically recommend so I would stick with it. A lot of knowledge and experience goes into their parts. They're also easy to use and incredibly reliable . For your 2012 Honda CR-V I recommend the following:
-Roadmaster Direct-Connect Base Plate Kit - Removable Arms # RM-521567-5
-Roadmaster Falcon All-Terrain Tow Bar # RM-522
-RoadMaster 68" Single Hook, Coiled Safety Cables... view full answer...
The TDE 46210 is going to be same as a typical 3,500lb hub with 5 on 4-1/2" bolt pattern. We have a few options for this depending on what you are looking for and if your axle has the easy grease fitting on the end of the spindle.
Standard Painted # AKIHUB-545-35-K
Easy Grease Painted # AKIHUB-545-35-EZ-K
Standard Galvanized # AKIHUB-545-35-G-K
Easy Grease Galvanized # AKIHUB-545-35-G-EZ-K
Stainless Steel # KH84545S
If you choose the stainless steel you will need an Inner Bearing # L68149,... view full answer...
The Curt Custom Tail Light Wiring Kit for Towed Vehicles # C96JR can be used with your LEDs, the only caveat is that if your Jeep has ParkSense proximity sensors then you'd need to use the Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles # RM-152-98146-7 instead. view full answer...
The Hayes brake controller bracket # HA81793B was designed to have the controller slide in from the front. There's a lever on the side of your Hayes Energize III part # HA81742B that would prevent it from being able to slide in from the back. So you would need to unplug the controller, slide it in from the front, and then replug the controller back in. view full answer...
Based on images I could find of Lark enclosed trailers with a double rear door it looks like you are going to need the Kit # PLR258-002. This will give you the mounts, handle, and catches for your trailer but you will need to source the 3/4" steel pipe and hardware needed locally and have the handle and cams welded to the pipe.
If you have something different from this type of setup please send me your images and dimensions for the parts you are looking to replace. view full answer...
Hey Scott, thanks for the question, and yes, the arms by themselves are something you can get for the Roadmaster Direct-Connect Base Plate Kit # RM-523193-5. What you will need for that is the following:
- Roadmaster Replacement Arms for Base Plate Kits # RM-ARMS
Just note that you'll need to click on the "Installation Details" link on the # RM-ARMS page and fill out the bracket form to get the right set. view full answer...
Your Firestone Ride-Rite Air Helper Springs # F2525 are not going to be compatible with the Curt Custom Fifth Wheel Installation Kit # C16441-204. It does appear to install any hitch with custom side plates you would have to switch to a different set of Air Springs like the Air Lift for 2WD # AL88228 or 4WD # AL88200.
Otherwise if you install the rails with the Universal Kit # C16200 then you could use the Curt Above-Bed Gooseneck Trailer Hitch # 16055 you found. Do note the universal... view full answer...
Welcome back! Yes, we do have a network of approved installers that will help you get the etrailer item # e33ZR and the item # 119250KIT installed on your 2019 Tesla Model 3.
I have attached the link below but you can also find it on the left hand side of all of our product pages below the pics and install videos. You will want to click on the link that says Locate installers near me. Once you've gotten to that page you will want to input your zip code. Doing this will give you a list... view full answer...
Hello there Frank, and thanks so much for that info. The answer to your question is 100 percent yes, you can use one of the Dexter Over/Under kits on your Jayco travel trailer with 3,500 lb Lippert axles. Those are 2-3/8" diameter axles, so the correct kit is the following:
- Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00 view full answer...
We only carry the Curt Powered Tail Light Converter # C59236 which is a universal wiring harness that is confirmed to work with the wiring on your 2013 Land Rover Range Rover Sport. This will give you a 4-way flat connection and should be much less expensive than any dealer available option. view full answer...
Yes there is. The Demco Autoslide 5th Wheel Trailer Hitch # DM8550034 is one option that could potentially be used in a Ford F-150 or F-250. This hitch is made to work with the industry standard fifth wheel rails, so provided both trucks have standard fifth wheel rails in the bed, the hitch will be transferrable.
That said, if both trucks do have the industry standard fifth wheel rails in the bed, pretty much any sliding 5th wheel hitch would be transferrable. As long as the hitch is... view full answer...